Relife RL-601L Mini Rotary Fixture for Mobile PCB Repair
₨ 4,200
Relife RL-601L Rotary Fixture
The Relife RL-601L rotary fixture clamps a phone motherboard on your bench and turns 360°, so you reach every edge without re-seating the board. An aluminum alloy body, a spiral shaft lock and a two-way card slot clamp hold boards of different shapes without rebound. The alloy steel base resists heat and corrosion, and silicone feet keep the fixture planted while you work with hot air or a soldering iron. Mechanicpk supplies it to Pakistani repair benches for board soldering, chip de-gluing, board removal, and fingerprint sensor and camera work.
In stock
RL-601L Mini Rotary Fixture for Motherboard Rework
The Relife RL-601L rotary fixture holds a phone motherboard steady and rotates 360°, so you work every side of the board from one clamped position. Pakistani repair benches handle hardware fault boards all day: dead phone motherboards, camera and fingerprint sensor jobs, and chips that need de-gluing before removal. This Mini fixture gives that work a fixed, repeatable hold instead of a board sliding around under your tweezers. Mechanicpk lists it as a precision workholding accessory, and it suits technicians who already know how much a steady board changes the quality of a rework.
Clamping Design and Build Materials
The body and the adjustment knob use aluminum alloy, and the thumbwheel gives you fine control as you close the clamp. A spiral shaft locks the board without rebound, so the grip stays where you set it. Relife upgraded the screw so you tighten it in seconds, and the knob moves smoothly under your fingers. Two-way clamping works through precision card slots and step sliders, and the step design adapts to different working setups. The card positions use synthetic stone with a hollow design that helps dissipate heat, which matters when your hot air nozzle sits close to the board. The 360° rotating step buckle lets you turn the fixture to present boards of different shapes at the angle you need.
Heat Handling and Bench Stability
The base uses an alloy steel plate, and the listing describes it as strong, stable, high-temperature resistant and corrosion resistant. Silicone feet resist wear and grip the bench, so the fixture stays put when you rotate a clamped board or press a probe against it. The listing also states high-temperature resistance and anti-static properties. Relife does not publish a maximum temperature rating, so set your hot air station within normal board-safe limits and keep the nozzle moving. Wipe flux residue off the card slots after each job. That keeps the clamp surfaces clean and the grip consistent from one board to the next.
Where It Fits in Your Repair Workflow
You use this fixture at the rework stage of the repair process. Clamp the board, rotate it to the working side, then run your IC change karna or de-gluing job with a hot air station or a soldering station. Rotating the clamp lets you reach chip edges for de-gluing without pulling the board out. When a dead phone needs jumper lagana for ISP work, the fixture holds the board still while you solder wires to the pinout points, and your ISP pinout tools stay connected. It also supports fingerprint sensor and camera maintenance, which the product listing names as intended uses. Pair it with a microscope for fine pad inspection, a multimeter for continuity checks after the job, and a reballing kit when a BGA chip needs fresh balls. If your bench grows, browse the PCB Holders category for fixtures that cover larger or more specialised boards.
The RL-601L Mini serves technicians who want one universal holder for varied board shapes rather than a jig cut for a single model. It does not target specific phone models, so you can use it across Android and other motherboards, provided the board fits the clamp. Check your board against the clamp before you start, because Relife does not publish a minimum or maximum board size.
| Weight | 0.35 kg |
|---|
Key Features
- ✓360° rotating step buckle for boards of different shapes
- ✓Aluminum alloy body and knob with a smooth thumbwheel
- ✓Spiral shaft lock that fixes the board without rebound
- ✓Upgraded screw that tightens in seconds
- ✓Two-way clamping with precision card slots and step sliders
- ✓Synthetic stone card positions with a hollow, heat-dissipating design
- ✓Alloy steel base that resists high temperature and corrosion
- ✓Silicone anti-slip feet, with heat-resistant and anti-static properties
Specifications
| Brand | Relife |
|---|---|
| Model | RL-601L Mini |
| Category | Motherboard Fixture / PCB Holder |
| Compatibility | Universal mobile phone motherboard fixture, not device-specific |
| Material | Aluminum alloy body and knob, synthetic stone card positions, alloy steel base |
Common Repair Uses
- ✓Holding a board still for rework, heat work and sensor repair.
- ✓Motherboard soldering
- ✓Chip de-gluing before removal
- ✓Board removal and maintenance
- ✓Fingerprint sensor maintenance
- ✓Camera maintenance
- ✓Holding a board for hot air work
- ✓Holding a board while you solder ISP wires
Compatible Devices
- ✓Universal fixture. It holds mobile phone motherboards of various shapes and is not tied to specific phone brands or chipset families.
- ✓Mobile phone motherboards of various shapes
- ✓Boards that need soldering or rework
- ✓Boards with chips that need de-gluing
- ✓Fingerprint sensor modules
- ✓Camera modules



