Relife RL-044 XM17 Stencil for MTK Xiaomi BGA Reballing
₨ 599
Xiaomi MTK BGA Reballing Stencil
The Relife RL-044 XM17 Stencil gives your bench a 0.12mm plate cut for Xiaomi, Redmi Note and POCO boards that run MediaTek Dimensity 700 to 1200 processors. You place it over cleaned CPU pads, spread paste or drop balls, and reflow to rebuild an even ball array in one pass. Coverage includes the Redmi Note 10 to 12 Pro range plus POCO M3 Pro, M4 Pro and X3 GT, and it reaches support ICs such as the MT6315GP, MT6360, MT6359 and MT6365. Reach for this stencil when a dead phone traces back to lifted or damaged CPU solder joints.
In stock
Relife RL-044 XM17 Stencil for Xiaomi MediaTek Boards
The Relife RL-044 XM17 Stencil works as a Xiaomi MTK BGA reballing stencil for technicians who rework Dimensity-based Redmi and POCO boards. XM17 belongs to Relife’s Xiaomi XM series, which runs from XM1 to XM17, and this plate carries the ball layout for the MediaTek platforms covered below. The 0.12mm steel plate gives you a fixed alignment reference, so you stop judging ball placement by eye on a board that already cost your customer a working phone. Mechanicpk lists it for shops that reball CPUs every week and want the same result on every pass.
Chipset and Device Coverage
Relife matches this plate to the Dimensity 700, 810, 920, 1080, 1100 and 1200 platforms, with the MT6833V, MT6877V and MT6893Z processor codes. On the phone side, that covers Redmi Note 10, 10 Pro, 11, 11 Pro, 11 Pro+, 11E, 11R, 12 Pro and 12 Pro+, plus POCO M3 Pro, M4 Pro and X3 GT and the K40 Game Enhanced. The coverage also reaches support ICs near the CPU, including MT6315GP, MT6360, MT6359, MT6365, MT6635XP and BQ25980. Read the marking on your chip before you order. A stencil only works when its aperture map matches the package exactly, and no amount of heat or patience rescues a mismatched plate. Check the board revision as well, because Xiaomi sometimes ships the same phone name with different processor variants.
Where It Fits in Your Repair Workflow
Reballing starts after diagnosis, never before it. When a Redmi reaches your bench as a dead phone, a boot loop issue or a hang on logo case, rule out software first. Reflash the unit, then check the storage path with your eMMC programmers and ISP pinout tools. Measure the main rails with a multimeter and hunt for shorts before you touch the CPU. Once the symptoms point at weak CPU joints, you lift the chip with your hot air station, clean the pads with flux and braid under a microscope, and lock the board in a PCB holder. Align the 0.12mm plate on the pads, apply paste or balls, and reflow with controlled heat. Let the board cool, peel the plate, inspect every ball under magnification, and then place the chip.
Why a Dedicated XM Plate Beats a Universal Mesh
A universal mesh forces you to shift balls across holes that never quite match the package, and every shift adds bridging risk. A model-specific plate removes that guesswork and shortens each job, which matters when a shop handles several Redmi Note boards a day. Relife rates its RL-044 range for high-temperature resistance and no deformation, and it checks each stencil against original factory drawings so every pad position stays covered. If you also work on Samsung or Huawei boards, the RL-044 range includes matching SAM and HW series plates, so one stencil family covers most of your Android reballing queue. As your volume grows, step up to a stronger soldering station, a binocular microscope, and a full reballing kit to pair with this plate.
| Weight | 0.14 kg |
|---|
Key Features
- ✓0.12mm steel plate with a fixed ball layout for Xiaomi MediaTek CPUs
- ✓Part of the XM1 to XM17 Xiaomi series in the Relife RL-044 range
- ✓Covers Dimensity 700, 810, 920, 1080, 1100 and 1200 platforms
- ✓Matches MT6833V, MT6877V and MT6893Z processor codes
- ✓Reaches support ICs including MT6315GP, MT6360, MT6359, MT6365 and BQ25980
- ✓Fits Redmi Note 10 to 12 Pro+ and POCO M3 Pro, M4 Pro and X3 GT
- ✓High-temperature resistance and no deformation across the RL-044 range
- ✓Light 0.01 kg plate that handles easily with tweezers on a PCB holder
Specifications
| Brand | Relife |
|---|---|
| Model | RL-044 XM17 |
| Category | BGA Reballing Stencil (Xiaomi / MediaTek series) |
| Compatibility | Xiaomi, Redmi Note and POCO boards with MediaTek Dimensity 700, 810, 920, 1080, 1100 and 1200 processors (MT6833V, MT6877V, MT6893Z) |
| Supported Devices | Redmi Note 10 to 12 Pro+, POCO M3 Pro, POCO M4 Pro, POCO X3 GT, K40 Game Enhanced |
| Technology | 0.12mm steel BGA stencil plate |
| Material | Steel |
| Weight | 0.01 kg |
Common Repair Uses
- ✓CPU reballing and support IC rework on Xiaomi MediaTek boards
- ✓CPU reballing after hot air chip removal
- ✓Rebuilding ball arrays after drop damage
- ✓Dead phone cases traced to weak CPU solder joints
- ✓Boot loop issue and hang on logo cases with poor CPU contact
- ✓Dead after flash boards that fail the software checks
- ✓Rework of support ICs such as MT6315GP, MT6360, MT6359 and MT6365
- ✓Pad preparation and ball inspection before chip placement
- ✓Charging issue boards that point to BQ25980 or MT6360 area faults
Compatible Devices
- ✓Xiaomi, Redmi Note and POCO boards on MediaTek Dimensity 700 to 1200 platforms
- ✓Redmi Note 10 and Note 10 Pro
- ✓Redmi Note 11, Note 11E and Note 11R
- ✓Redmi Note 11 Pro and Note 11 Pro+
- ✓Redmi Note 12 Pro and Note 12 Pro+
- ✓POCO M3 Pro
- ✓POCO M4 Pro
- ✓POCO X3 GT
- ✓K40 Game Enhanced
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which Dimensity chips does the Relife RL-044 XM17 stencil cover?
What thickness is the Relife RL-044 XM17 stencil plate?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



